How To Repair Hole In Wood Grain Door
Download Article
Download Commodity
It's pretty easy to accidentally knock a hole in a hollow-core door, but fortunately, it'due south also pretty easy to set up! We'll show you how you can get your door looking like new once again with but a lilliputian fourth dimension and a few materials from the hardware store.
-
ane
Cut any loose plywood away from the edges of the hole. The pigsty in your door probably has some loose plywood around the ragged edges. Employ a utility knife to cut this textile away, until you lot're left with a clean hole with smooth edges.
-
2
Pack a couple of paper towels into the pigsty. Push in three or 4 paper towels, until they're firmly set in identify and won't slip lower within the door. You'll need the newspaper towels in the hole to support the expanding foam you lot're nigh to add. Without the paper towels, the foam would autumn to the bottom of the hollow door.
- Newspaper towels are light enough that they tin back up their own weight past creating friction against the inner walls of the hollow door.
Advertisement
-
3
Fill the hole with expanding foam insulation. This cloth comes in a large aerosol can with a long plastic applicator tip. Squirt a generous amount into the hole, and so that the cream expands to fill up the hollow space behind the hole. Allow the cream to dry.[one] This will accept several hours, so information technology'southward best to let it dry overnight.
- Y'all can purchase foam insulation at any local hardware store or home-supply store. If the store has a variety of options, purchase a low-expansion type. This will get out you with less cleanup.
Advertizement
-
1
Cut the protruding cream. Once your expanding foam has dried, it will have expanded significantly and may extend a couple of inches away from the door. Using your utility pocketknife, cutting the excess foam abroad until the foam is slightly lower than the surface of the door.[2]
- The expanding foam needs to be completely dry out before you kickoff trimming. If the center of the foam is still moisture, expect a few hours until it'due south fully dry out.
-
2
Mix auto-body filler and a hardener catalyst at a ii:ane ratio. Scoop or squeeze an automobile-body filler out of its container and into a disposable bowl or any sort of plastic tray. Then squeeze in half equally much hardener goad. This cloth will rapidly harden and cover the outside of the door pigsty. These are both thick, putty-similar liquids; use a popsicle stick to stir them until the substances are fully composite.[3]
- Start out with virtually one teaspoon (4.ix ml) of the automobile-body filler and half as much goad. Mix more every bit needed.
- Both motorcar-trunk filler (such as Bondo) and a hardener catalyst should be available at a large hardware store. If not, check a abode-supply shop or an automobile-trunk business organization.
-
3
Apply the filler mixture over the dried expanding foam. Use your popsicle stick to scoop upwardly some of the filler mix and smear it over the dried foam that'southward filling the hole in your door. This material will dry and harden apace, so y'all'll need to work fast.
- After about five minutes, one time the filler has started to thicken, take the border of a putty knife and scrape information technology across the filler. This will smooth the surface and remove any backlog, semi-dry out filler.
- Await to go on until the filler has fully dried.
-
4
Sand the filler with 100-grit sandpaper. [4] Employ the sandpaper to sand the fully dried filler until it's completely smooth and flush with the surface of the door. Also sand off any leftover expanding foam or filler that has stuck to the plywood door fabric around the edges of the hold you've filled.[5]
- Sandpaper of all grit consistencies will be available at your local hardware store.
Advertising
-
one
Apply spackle over the sanded filler. [vi] Utilize a putty knife to apply a layer of spackle over the hole.[7] Work in long, smoothen strokes to apply the putty equally smoothly as possible.[8] Allow the spackle to dry out once you've applied it. Give it most an hour.
- You can find spackle at whatever hardware or home-supply store.
-
2
Sand the pigsty once the putty has dried. [9] Have a sheet of sandpaper and rub it over the dried spackle until it'southward completely flat and smooth.[x] You can utilise 100-grit sandpaper for this task every bit well. You should use a dissimilar canvass from the 1 yous used to sand down the filler, though.
-
3
Apply a coat of paint over the pigsty [11] . Now the spackle has dried and been sanded downwardly, you're fix to finish fixing the pigsty. Use a large paintbrush to utilise a glaze of paint over the patched hole.[12] Work in long, polish strokes and so that the layer of paint looks equally uniform as possible. Requite the paint about an hour to dry, and at that point, the hole will exist fixed.
- The paint that you use should match the color of your door. In order to find a good lucifer, visit a pigment shop, bring abode multiple swatches, and find the color closest to that of your door.
Advertisement
Add New Question
-
Question
How do you repair a hole in a door?
Kevin Turner is a handyman and the owner of Red Gator Maintenance, a handyman business based in Fresno, California. Working on handyman-related projects since the age of 12, Kevin specializes in a wide variety of home improvement projects such as (just not limited to) lighting/electrical, plumbing, deck staining, drywall repairs, cabinet installation, air conditioning, trash removal, and window, roof, and appliance repairs.
Commercial Handyman
Skillful Answer
I would recommend filling in the hole with a heavy-duty auto-body filler. Once the filler dries, sand it shine. Then, add a layer of putty, sand that shine, and apply primer and paint.
Ask a Question
200 characters left
Include your electronic mail accost to become a message when this question is answered.
Submit
Advertisement
Things You'll Need
- Utility knife
- Expanding foam insulation
- Polyester resin (auto body filler)
- A hardener catalyst for the filler
- Popsicle stick
- Putty knife
- 100-grit sandpaper
- Spackle
- Paint which matches the colour of your door
- Paint brush
-
Exercise caution when using the utility knife. If you're not careful, the blade could hands slip and cut your hand. Practise not allow young children to play with the knife.
-
If the pigsty is really big, it might exist worth replacing the door altogether. Hollow-cadre doors aren't that expensive, so it'south not that big of a burden.[thirteen]
Advertisement
About This Commodity
Article Summary 10
To fix a hole in a door, beginning by stuffing a few newspaper towels in the hole and filling it with expanding foam insulation. And then, once the foam has dried, cutting off the backlog and employ an auto-body filler mixed with a hardener catalyst over the spot. Side by side, let the filler dry, and then sand information technology with 100-grit sandpaper so it's polish and affluent with the rest of the door. Finally, spackle over the filler, sand it downwardly, and apply a glaze of paint over it. For tips on how to use auto-body filler, whorl down!
Did this summary assist yous?
Thanks to all authors for creating a folio that has been read 37,209 times.
Did this article help you?
Source: https://www.wikihow.com/Fix-a-Hole-in-a-Door
0 Response to "How To Repair Hole In Wood Grain Door"
Post a Comment